Virginia Tech® home

24 Ways to Kill a Tree

ID

430-210 (SPES-307P)

Authors as Published

Authored by Bonnie Appleton, Extension Specialist, Hampton Roads AREC and reviewed by David Close, Consumer Horticulture and Master Gardener Specialist, School of Plant and Environmental Sciences, Virginia Tech

Few residential trees die of “old age.” Mechanical damage and improper tree care kill more trees than any insects or diseases. Avoid making the tree-damaging mistakes shown in the diagram below. Few of these items alone would kill a tree, but multiple problems will certainly stress, and could eventually kill, a tree.

A numbered diagram of a tree which corresponds to the listed items.
 
  1. “Top” tree to encourage watersprouts that weaken tree and encourage pests.
  2. Leave co-dominant leaders to encourage “V” growth and splitting during winds and storms.
  3. Leave crossing branches to rub protective bark and create wounds.
  4. Ignore insect or disease damage.
  5. Coat pruning cuts with paint or sealer to slow healing and promote pest problems.
  6. Leave broken branches unpruned to encourage pests.
  7. Spray unapproved herbicides over tree root area to weaken tree.
  8. Damage roots and trunk with lawn equipment.
  9. Rip through roots when digging trenches.  
  10. Plant close to house or obstacle to reduce adequate tree and root growing space.
  11. Attach items to tree to damage bark and girdle branches with wire and rope.  
  12. Prune randomly to leave branch “stubs.”
  13. Prune flush cuts to reduce wound closure.  
  14. Leave tree staked until guy wire girdles trunk.  
  15. Leave wrap on to constrict trunk growth and rot bark.
  16. Pile up excessive mulch to encourage rodent damage and bark rot.  
  17. Put non-porous black plastic under mulch.
  18. Stack items atop roots to cause soil compaction.
  19. Leave ball roping on to girdle trunk.
  20. Plant near downspout to assure excessive water or water lightly to encourage shallow root growth.
  21. Leave top of wire basket in place to girdle roots.
  22. Leave treated or synthetic burlap on to prevent root growth.
  23. Dig hole too narrow and over amend backfill to discourage proper root spread.
  24. Dig hole too deep or fill with gravel to collect water and drown roots.

How NOT to Kill a Tree

  1. Do not top trees. Tree heights can be lowered by proper crown reduction that does not stimulate watersprout production.
  2. When a tree is young, select one or the other of the competing upright branches to be the main branch and properly remove the other.
  3. Remove branches that cross and rub in order to prevent bark wounds.
  4. Monitor for insects and diseases and treat appropriately if they are found and specifically identified.
  5. Do not use anything to cover pruning cuts or wounds – trees seal their own wounds.
  6. Cut broken branches off at the branch bark collar.
  7. If you treat your lawn, only use herbicides that will not damage trees.
  8. Mulch around the tree to avoid hitting the tree trunk with lawn or edging equipment and to protect surface roots.
  9. Dig around roots whenever possible but when not, make a clean pruning cut on the tree side of the root.
  10. Know how big a tree will grow (height and width) and space accordingly away from houses and other obstacles.
  11. Insert a nail or screw into your tree to which a wire or line can be attached. The tree will seal around the small wound made by the nail or screw.
  12. Cut branches back to laterals so you do not leave stubs to which the branches will die back.
  13. Do not make flush cuts. Cut on the outside of the branch bark collar.
  14. Stakes generally are not needed on small residential trees, but if they are, remove them after one year to avoid any damage.
  15. Do not wrap the trunk with anything except a wide wire cage if animals are a problem.
  16. Do not put mulch in contact with the trunk, and then pile mulch only 2 to 3 inches over the roots.
  17. Do not put any type of fabric or plastic material under your mulch.
  18. Do not stack items atop the roots; it causes soil compaction.
  19. Take the ball roping off around the tree trunk. If the tree is in a container, remove the container before planting.
  20. Divert water from the roots of trees that do not like wet soil, but when you water, water deeply to encourage deep root growth.
  21. Remove the wire basket.
  22. Remove the burlap, regardless of type, from the ball.
  23. Dig the hole at least twice as wide as the root system to encourage lateral root growth out of the root ball. Do not amend backfill for individual tree holes. Only amend if the entire planting area can be equally amended.
  24. Dig your hole only as deep as the root system and do not put gravel in the bottom of the planting hole unless you install a drain to actively pull extra water away

Additional Extension publications that can help you with tree planting and pruning: 430-295 and 430-455 through 430-462 at www.resources.ext.vt.edu.

Poster concept designed by Bonnie Appleton

Poster initally funded by a Virginia Urban and Community Forestry assistance grant.

Reviewed by; Dan Goerlich, Adam Downing, Guy Mussey and Roger Harris


Virginia Cooperative Extension materials are available for public use, reprint, or citation without further permission, provided the use includes credit to the author and to Virginia Cooperative Extension, Virginia Tech, and Virginia State University.

Virginia Cooperative Extension is a partnership of Virginia Tech, Virginia State University, the U.S. Department of Agriculture, and local governments. Its programs and employment are open to all, regardless of age, color, disability, sex (including pregnancy), gender, gender identity, gender expression, national origin, political affiliation, race, religion, sexual orientation, genetic information, military status, or any other basis protected by law

Publication Date

March 9, 2021